Welcome Cornucopia! - November 2022 Mood Board + Mixed Media Kit
Hey, y’all! This week I grabbed up the November 2022 Mixed Media Kit, the burlap flowers from the Scrapbooking Kit, and a couple items from my stash to create a fabulous fall décor piece!
The only mediums I used for color were the four Stencil Butters that came in the kit – it was all just a matter of how I mixed and layered them to create the different shading.
Make sure you check out the video to catch all the details of what I did to bring my cornucopia to life!
This project really was rather simple – I let the stencil butters and the texture powder do the heavy lifting for me!
I didn’t use any gesso on the surface because I didn’t want too many layers that may make it more difficult for me to see the laser cut details on the Tres Jolie cornucopia base. The first thing I did was grab up some artist’s tape and tape off the border between the edge of the filling and the basket, then I brushed a thin coat of the Chocolate Stencil Butter all over the basket. To start getting some detail built up, I then mixed some of the Chocolate Stencil Butter with some of the texture powder and used some small round brushes to create the raised areas of the basket – or the areas that I thought of as raised!
Since I had a little of that mix left, I brushed it on to the lower part of the base then used a baby wipe to clean it up – just leaving some of the color behind to start filling in the areas between all of the foliage and produce.
Once all of the Chocolate Stencil Butter had dried, I started working with the Fern in the same fashion. I mixed in some texture powder and started building up the apple and some of the foliage. Then, to create some variations in shading, I mixed in some of the Eggplant Stencil Butter for the pear, and to create the darkest of the green, I added some of the Terra Cotta and Chocolate. Then I just brushed the Fern Stencil Butter on straight from the jar to add the light areas to the apple and pear and some lighter highlights to the foliage.
I also wanted to add a little lighter coloring to the basket, so I brushed on my leftover mix, sprayed it down with water, and wiped up most of what was there – leaving just enough to add a hint of color besides the Chocolate.
The raised area of the pumpkin is made up of some of the texture powder mixed with the Terra Cotta, and after that had dried, I came back with some of the Terra Cotta straight from the jar and filled in the smaller areas and I used my finger to rub a thin, uneven layer on top of the texture powder mix.
Since I loved the unevenness of using my finger to rub on the Stencil Butter, I decided to add some of the Terra Cotta to the cornucopia basket and rub on some of the Chocolate along the edges.
For all of the grapes (berries?) I used a cheap cake piping bag and tip with the Eggplant Stencil Butter and just created all of my “dots”! I think it made the process go a lot quicker than if I had tried to use a brush. I just sprayed the surface of the Stencil Butter with water and made a little puddle to dip my finger in so I could smooth out any areas – so long as either my finger or the surface of the Stencil Butter was kept wet, my finger didn’t get stuck!! To really get those grapes to pop, I grabbed up my heat gun and (for once) I purposely “overheated” my texture paste/stencil butter to create bubbles!
For the grape stems, I just mixed some texture powder, Eggplant, and Fern together and brushed it on. Then I watered it down and added that green-ish hew to the inside of the basket, and then used up the rest to give my metal “Welcome” a coating. Once again, I didn’t use any gesso, I just brushed my Stencil Butter directly on the surface. After that layer had dried, I used a soft brush and added some of the Eggplant to the upper half (and back) of the metal word.
For my stand, I up-cycled two of the hanging bars from a hanging file folder, bending one around to create the bottom and cutting the second in half to create the two uprights behind the cornucopia. I used some Gorilla Clear Grip to hold the metal in place, then came back with some 3D Matte Gel for extra adhesion and to hold the “Welcome” in place. I mixed some of the Chocolate Stencil Butter with some of the texture powder and some of the 3D Matte Gel for adhesive power then brushed a layer on to the metal bars. I grabbed my heat gun up so I could get the surface of the mix dry, then added my flowers with some 3D Matte Gel.
After all of my gel had dried, I came back and just added some touch up areas to the stand and word, then gave a coating of the Chocolate to the back for a more finished appearance.
That was it! It wasn’t a super complicated project, just a matter of mixing colors and trying to keep as much detail as possible! Thank you for joining us here at Tres Jolie, I hope you enjoyed this project, and it gave you some ideas of what you can do with your Mixed Media Kit this month!
Stay Crafty, Friends
Did you get a kit? Share what you made in our Facebook Group!
Thank you for joining us here at Tres Jolie Kits!
Tres Jolie can also be found at:
Finnabair 3D Matte Gel , Gorilla Clear Grip , piping bag/tip , Chandler Heat Gun , Crafter’s Square Metal Words , hangers from hanging file folders