Ornaments! - December 2022 Mood Board
Hey, y’all! Yesterday was the first day of winter (Winter Solstice), today is the 4th-5th day of Hanukkah (the 5th day of Hanukkah will start at sundown tonight, if my counting is correct – if I’m wrong, feel free to correct me!), Christmas is on Sunday, Kwanzaa starts Monday, and 2023 is ten days away! It’s been a year I tell ya! Don’t worry though, this isn't my last project for 2022, I still have one more for you next week!
This week I have some ornaments for you I made using this month’s Cards, Tags, & More and Mixed Media Kits. Although, the Mixed Media Kit ornaments took a while to dry and haven’t been 100% completed. They weren’t part of my original plan – I had only planned on the three “double” ornaments made using the papers and cardstock from the Cards Kit. (Check out the video to get the details about all the how's and why’s!)
...
...
My ornaments are also for the mood board challenge – what is a better holiday tradition than handmade ornaments or décor? For me, Christmas Trees need the ornaments my kiddos made – even if it has been close to a decade since the last one was made!
...
For the blog, I'm just going to talk about what you're seeing in the photos, the video is where you can watch my thought process in action!
All of the clear plastic ornaments are 4-inches, and none of my inner, paper ornaments are over (approximately) 2-5/8-inches in diameter.
 |
 |
 |
For this first ornament, I cut four circles, in each size, out of one of the sheets of patterned paper and one of the cardstock sheets from the kit. After I had them together – not all the way “closed” – I added a touch of embossing powder along the edges, then I glued a hat pin along the centers, using a small bead as separators.
I wanted to add a bit of a frosted look to this ornament, so I grabbed up some Finnabair Crushed Crystal and dabbed onto the inside, keeping to the outer edges so the center would remain mostly clear, allowing the inner ornament to show. I used a combination of hot glue and 3D Matte Gel to hold my ornament in place – the hot glue to tack it in place long enough for the gel to dry – and after all the mediums had dried, I glued my halves together.
This ornament was my “experiment” with Foundry Wax – I had assumed the plastic would not hold up to the heat needed for the Foundry Wax, but I experimented so you wouldn’t have to! My official stance is – don’t use mediums that need to be heat set!
 |
 |
 |
This second ornament is made up of four circles cut from one of the patterned papers and four circles cut from one of the cardstock sheets. I used a touch of paint along the edges, nothing that stands out, just a bit of White Pearl Metallic Paint. Once again, I didn’t close up my inner ornament until I had glued in what I was using to suspend in within the clear plastic ornament – in this case a bit of gold (costume jewelry) chain. I added the gold Little Birdie wreaths to the sections that were made of the cardstock, used my hot glue and 3D Matte Gel to start the process of holding everything in place – then decided that wasn’t enough!
As I was looking at this ornament, I decided it need a little something more – not frosted like the first one – but something, so I grabbed up some glitter and added it to the top and bottom of the ornament, trying to create the look that the chain was coming out of the glitter “mound.” After I had the two halves glued together, I still thought there should be more, so I did something rare – I added glitter to the outside of a project! I just used some (regular weight) matte gel since it wouldn’t run the way glue might to hold the glitter in place and set it off to dry.
 |
 |
 |
For my third and final (actually finished) ornament, I used a small doily die to cut out four pieces of patterned paper and four pieces of cardstock, then glued them together the same way I did all the circles in the other two ornaments. Since this patterned paper is a darker and busier print, I only added a touch of the Bubbly Embossing Powder from this month’s Mixed Media Kit to the edges and wrapped the “Holly” and “Jolly” Tres Jolie Chipboard words around the center. The chipboard words are embossed in a layer of the Bubbly powder, and an extra layer of Lindy’s Holly Berry Red Gold on the bottom half-ish to create a bit of a gradient effect.
I was attempting to create the illusion that the inner ornament was floating within the outer ornament, so I used a length of fishing line to suspend it inside – just adding a few small beads to give it a little “extra.” I didn’t add any mediums to my outer ornament besides the bit of Vintage Gold Finnabair Wax – after adding a light coat of clear gesso - at the top where the hook will go.
Alright, as I stated in the video, I have a photo here for you of the two ornaments that had the Distress Mica Sprays and some glittery mediums in them – that took for-EV-er to dry! They are dry now, but they weren’t dry soon enough to do anything else with – that would also need time to dry! They were unplanned, I just needed something to experiment on before doing “things” to my planned ornaments! I’m hoping that I will finish these unplanned ornaments before next December!
Thank you for joining us here at Tres Jolie, I hope you enjoyed these ornaments, and they gave you some ideas of what you can makes using this month’s kits.
Stay Crafty, Friends
...
Did you get a kit? Share what you made in our Facebook Group!
Thank you for joining us here at Tres Jolie Kits!
...
Tres Jolie can also be found at:
...
 |
 |
In addition to this month’s Mixed Media Kit and Cards, Tags, & More Kit (*from previous Tres Jolie Kits), I used:
*Finnabair “White Pearl” Metallique Paint , *Finnabair “Crushed Crystals” Jewel Effect Paste , *Cosmic Shimmer “Sparkle Texture Paste , Distress Foundry Wax “Gilded” (although, I don’t recommend heat with plastic ornaments!) , *Lindy’s Gang “Holly Berry Red Gold” Embossing Powder , *DecoArt Gold Glitter , *DecoArt Crackle Glaze , Shimmerz Paint “Puttin’ On The Glitz” Paste-Eez , Distress Clear Embossing Ink , *Dress My Craft “Classic Doily” Die , Spellbinders Standard Circle Nestabilities , Gorilla Hot Glue Sticks , 4” clear plastic ornaments, hat pin , gold chain (costume jewelry) , fishing line , gold beads , Art Glitter Glue , JudiKins Diamond Glaze